Subaru Legacy

since 1990-1998 release

Repair and operation of the car



Subaru of Legasi
+ 1.1. Identification numbers
+ 2. Maintenance
+ 3. Engines
+ 4. Heating, ventilation
+ 5. Fuel system
+ 6. Exhaust system
+ 7. Systems of start, ignition
+ 8. Transmissions
+ 9. Coupling, shaft
+ 10. Brake system
+ 11. Suspension bracket
+ 12. Steering
- 13. Body
   13.1. Introduction
   13.2. Care of a body
   13.3 Care of an upholstery and rugs
   13.4. Repair of insignificant damages of a body
   13.5. Repair of strong damages of a body
   13.6. Cowl
   13.7. Replacement of the lock of a cowl
   13.8. Replacement of a cable of the lock of a cowl
   13.9. Front grille
   13.10. Front bumper
   13.11. Rear bumper
   13.12. Forward wing
   13.13. Door upholstery
   13.14. Lock, cylinder of the lock and handle of opening of a door
   13.15. Door glass
   13.16. Window regulator
   13.17. External mirror
   13.18. Doors
   13.19. Trunk lid
   13.20. Luggage carrier lock
   13.21. Cable of opening of the lock of a luggage carrier
   13.22. Replacement of racks of support of a back door
   13.23. Back door
   13.24. Lock of a back door, external handle and cylinder of the lock
   13.25. Casings of a steering column
   13.26. Central console
   13.27. Dashboard elements
   13.28. Dashboard
   13.29. Air inlet lattice
   13.30. Forward seats
+ 14. Electric equipment


3a942d17

13.2. Care of a body

GENERAL INFORMATION

Check of a condition of a body has to be made regularly. Otherwise corrosion of separate sites of a body can lead to its strong damage and further expensive repair. It is also important to pay attention to parts of the car inaccessible to an external look, for example, to the bottom, arches of wheels and the lower part of a motor compartment, and also parts of a body, hidden under an upholstery. A basic element at care of a body is its sink. Before a wash of the car soak insects and remove from a body surface. Plentifully use water. Use a soft sponge or a soft brush. The varnish covering cannot be washed with a stream with a strong pressure. Pour over the car from a hose and wash away dirt from top to down. Often rinse a sponge. Wipe the car pure rags. Apply only the good degreasing washing substances. For the purpose of protection for a sink add the washing preservatives to water. It is forbidden to wash and dry the car on the sun, otherwise on a varnish surface there will be spots. Salt with which strew roads, makes harmful effects on a car body.


Prevention

After a wash of the car because of humidity efficiency of action of brakes decreases. It is recommended to dry brake disks short-term pressing a brake pedal in a start of motion.


Preservation

Purely washed up and dried up varnish covering needs to be processed every 3 month the preserving means to protect a car surface from atmospheric influences by creation of a pore-free water-repellent wax layer.

At once to remove the flowed-out fuel, oil or greasing, and also brake fluid, differently color of a varnish covering will change.

Processing of a surface needs to be repeated if water does not gather in drops, and spreads on a surface. Regular processing by the preserving means promotes long preservation of gloss of a varnish covering.

There is also other possibility of protection of varnish coverings – by means of the washing preservatives. However the washing preservatives provide reliable protection of varnish coverings only in case are used at each wash of the car and at least, than in 2–3 weeks.

After use of the washing (foam-forming) means additional processing of a surface by preservatives especially is recommended.
Prevention

Preservation cannot be made on the open sun.


Polishing

Polishing of a varnish surface is necessary only in case it faded owing to insufficient leaving, influence of dust, harmful gases, weather conditions, and the preserving means cannot restore its gloss.

It is not necessary to apply rough polishing pastes and chemically active polishing means, despite previously good results.

Before polishing the car needs to be washed up and carefully to dry up. Further to adhere to the instruction on use of the polishing means.

To make polishing small sites in order to avoid premature drying of polish. After processing of a surface some polishing means it is necessary to make additional preservation. It is forbidden to polish on the open sun. Opaque varnish surfaces cannot be processed the preserving and polishing means.

Removal of spots of pitch

Pitch quickly diffundirut in varnish coverings, and it is impossible to remove it completely already. Fresh spots of pitch can be removed with the soft rag moistened in flushing gasoline. In case of emergency it is possible to use usual gasoline, kerosene or turpentine.

Removal of insects

Insects contain substances which can damage a varnish film if quickly not to remove them. Insects can be washed away only the weak slightly warm soap or washing solution or by means of special means for removal of insects.

Removal of construction solutions

Splashes of construction materials are washed away by slightly warm solution of neutral detergents. Strongly not to rub, differently it is possible to scratch a varnish covering. Then carefully to rinse with clear water.

Care of details from artificial materials

Plastic details, sitting from an imitation leather, a headlight, and also it is possible to wash the details painted in opaque black color with water with addition of special detergents. It is not recommended to wet. Plastic details can be processed if necessary special cleaners. Not to use nitrosolvent or gasoline at all.

Sink of glasses

To wipe glasses a pure soft rag from the internal and outer side. At strong pollution it is possible to use alcohol or liquid ammonia and warm water, and also special means for purification of glasses. At a windshield sink to lift screen wipers up.
Prevention

When using silikonosoderzhashchy means for cleaning of varnish coverings it is impossible to wipe them glasses. At dispersion of silikonosoderzhashchy aerosols of glass it is necessary to close a cardboard or other materials.


Care of rubber consolidations

Periodically to strew the condensing or sliding surfaces with talc or to spray silicone aerozolyyu. It will keep their elasticity and will exclude a scratch when closing doors. It is possible to eliminate unpleasant sounds, having wiped the adjoining surfaces liquid soap.

Disks of wheels

Disks of wheels from light metals demand leaving, especially in a cold season. For this purpose it is possible to use special means for cleaning of disks. Not to apply active, acidiferous, silnoshchelochny and rough cleaners or water with a temperature over + 60 °C.

Seat belts

Seat belts should be washed with weak alkaline solution, without removing them. Not to subject them to dry cleaning which can cause destruction of fibers. To twist belts with automatic winding in the dried-up state, if necessary to use special an aerosol for the best sliding. It is not recommended to dry belts at a temperature over 80 °C and on the open sun.