Subaru Legacy

since 1990-1998 release

Repair and operation of the car



Subaru of Legasi
+ 1.1. Identification numbers
+ 2. Maintenance
- 3. Engines
   3.1. Technical characteristics
   3.2. Operations on repair of the engine installed in the car
   3.3. Top dead point of the first cylinder
   3.4. Cover of a head of the block of cylinders
   3.5. Inlet collector
   + 3.6. Gear belt and pulleys
   3.7. Replacement of a forward sealing ring of a cranked shaft
   3.8. Replacement of sealing rings of camshafts
   3.9. Camshafts and pushers
   3.10. Heads of the block of cylinders
   3.11. Oil pallet
   3.12. Oil pump
   3.13. Drive flywheel / plate
   3.14. Replacement of a back sealing ring of a cranked shaft
   3.15. Suspension bracket of the power unit
   - 3.16. Capital repairs of the engine
      3.16.1. Technical characteristics
      3.16.2. Check of a compression
      3.16.3. Check of the engine by means of the vacuum gage
      3.16.4. Recommendations about removal of the engine
      3.16.5. Removal of the engine
      3.16.6. Sequence of dismantling of the engine
      3.16.7. Dismantling of a head of the block of cylinders
      3.16.8. Cleaning and survey of a head of the block of cylinders
      3.16.9. Assembly of a head of the block of cylinders
      3.16.10. Removal of pistons
      3.16.11. Division of sections of blocks of cylinders
      3.16.12. Removal of a cranked shaft with rods
      3.16.13. Block of cylinders of the engine
      3.16.14. Honingovaniye of cylinders
      3.16.15. Rods
      3.16.16. Cranked shaft
      3.16.17. Survey of radical and shatunny bearings
      3.16.18. Balance of assembly of the engine at capital repairs
      3.16.19. Survey of pistons
      3.16.20. Check of working gaps of shatunny bearings
      3.16.21. Check of working gaps of radical bearings of a cranked shaft
      3.16.22. Assembly of sections of the block of cylinders
      3.16.23. Installation of piston rings
      3.16.24. Installation of pistons
      3.16.25. Installation of the engine
      3.16.26. Start of the engine after capital repairs
+ 4. Heating, ventilation
+ 5. Fuel system
+ 6. Exhaust system
+ 7. Systems of start, ignition
+ 8. Transmissions
+ 9. Coupling, shaft
+ 10. Brake system
+ 11. Suspension bracket
+ 12. Steering
+ 13. Body
+ 14. Electric equipment


3a942d17

3.16.25. Installation of the engine

PERFORMANCE ORDER
1. Apply a thin film of high-temperature greasing on vents of the conducted transmission shaft.
2. Using the load-lifting mechanism, lower the engine in a motor compartment. At installation of the engine if necessary incline and turn it so that it was installed into place, without having done harm.
3. Combine a cranked shaft of the engine with the conducted transmission shaft. Move up the engine to a transmission and establish the top, and then lower bolts of fastening of a transmission to the engine.
4. Lower the jack supporting a transmission and remove it from under the car.
5. Finally lower the engine and remove slings of the load-lifting mechanism from the engine.
6. Raise the car so that it was possible to work under a motor compartment.
7. Fix engine support, having tightened bolts and nuts the demanded moment.
8. On models with an automatic transmission fix the hydrotransformer to a drive plate.
9. Establish a reception exhaust pipe.
10. Establish a coupling cable on the lever of switching off of coupling and adjust a cable.
11. Further installation is made in sequence, the return to removal.
12. Adjust a tension of driving belts.
13. Fill in oil in the engine and a transmission.
14. Fill in cooling liquid in the cooling system.