Subaru Legacy

since 1990-1998 release

Repair and operation of the car



Subaru of Legasi
+ 1.1. Identification numbers
+ 2. Maintenance
+ 3. Engines
+ 4. Heating, ventilation
+ 5. Fuel system
+ 6. Exhaust system
+ 7. Systems of start, ignition
+ 8. Transmissions
+ 9. Coupling, shaft
+ 10. Brake system
+ 11. Suspension bracket
+ 12. Steering
+ 13. Body
- 14. Electric equipment
   - 14.1. Electric equipment of a body
      14.1.1. Introduction
      14.1.2. Electric chains
      14.1.3. Detection of not closed chain
      14.1.4. Safety locks
      14.1.5. Chain breakers
      14.1.6. Relay
      14.1.7. Relay of turns and alarm light system
      14.1.8. Multipurpose switches of a steering column
      14.1.9. Ignition lock
      + 14.1.10. Replacement of switches of the dashboard
      14.1.11. Combination of devices
      14.1.12. Radio receiver
      14.1.13. Loudspeakers
      14.1.14. Antenna
      14.1.15. The antenna with the electric drive
      14.1.16. Replacement of bulbs of headlights
      14.1.17. Adjustment of light of headlights
      14.1.18. Headlight
      14.1.19. Replacement of bulbs of an incandescence
      14.1.20. Screen wiper engine
      14.1.21. Sound signal
      14.1.22. Check of a heater of back glass
      14.1.23. Window regulators with the electric drive
      14.1.24. Rear-view mirrors with the electric drive
      14.1.25. Safety airbag
   + 14.2. Electroschemes


3a942d17

14.1.20. Screen wiper engine

GENERAL INFORMATION

If brushes of a screen wiper work with interruptions or is insufficiently effective, check a condition of a safety lock in a screen wiper engine chain.

If the safety lock is serviceable, connect the closing wire between the engine of a screen wiper and mass of the car and repeatedly check operation of the engine of a screen wiper.

If now the engine of a screen wiper works normally, restore connection of the engine with the mass of the car.

If the engine still does not work, check giving of tension to the screen wiper engine.

If tension moves to the engine, and the engine does not work, remove the engine of a screen wiper and, using additional wires, connect it to the accumulator.

If the engine works now, check a condition of the electric socket. If the engine still does not work, replace it.

WINDSHIELD SCREEN WIPER ENGINE

Arrangement of bolts of fastening of the engine of a screen wiper on models from 1990 to 1994


Arrangement of bolts of fastening of the engine of a screen wiper on models since 1995


PERFORMANCE ORDER
1. Remove a weight wire from the accumulator.
2. Remove levers of a screen wiper and a lattice of an air inlet. Disconnect the electric socket from the screen wiper engine.
3. Unscrew bolts of fastening of the engine of a screen wiper.
4. Put forward the engine of a screen wiper and disconnect draft from the engine. If the engine of a screen wiper is subject to replacement, unscrew a nut, the fixing thirst of a screen wiper for an engine shaft.
5. If the engine is repeatedly installed, disconnect other end of draft of a screen wiper from the screen wiper lever. Take the screen wiper engine from the car.
6. Unscrew 6 nuts.
7. Plum of the party take drafts of a screen wiper.
8. Installation is made in sequence, the return to removal.

ENGINE OF THE SCREEN WIPER OF BACK GLASS

Arrangement of bolts of fastening of the back engine of a screen wiper on models from 1990 to 1994


Arrangement of bolts of fastening of the back engine of a screen wiper on models since 1995


PERFORMANCE ORDER
1. Unscrew a nut and remove the screen wiper lever.
2. Remove a protective head and unscrew a nut of fastening of a spindle of the engine.
3. Open a back door, remove an upholstery of a back door and remove a protective film from a door.
4. Disconnect the electric socket, unscrew bolts of fastening and take the screen wiper engine from a back door.
5. Installation is made in sequence, the return to removal.