Subaru of Legasi
+ 1.1. Identification numbers
+ 2. Maintenance
+ 3. Engines
+ 4. Heating, ventilation
+ 5. Fuel system
+ 6. Exhaust system
+ 7. Systems of start, ignition
+ 8. Transmissions
+ 9. Coupling, shaft
+ 10. Brake system
+ 11. Suspension bracket
+ 12. Steering
+ 13. Body
- 14. Electric equipment
- 14.1. Electric equipment of a body
14.1.1. Introduction
14.1.2. Electric chains
14.1.3. Detection of not closed chain
14.1.4. Safety locks
14.1.5. Chain breakers
14.1.6. Relay
14.1.7. Relay of turns and alarm light system
14.1.8. Multipurpose switches of a steering column
14.1.9. Ignition lock
+ 14.1.10. Replacement of switches of the dashboard
14.1.11. Combination of devices
14.1.12. Radio receiver
14.1.13. Loudspeakers
14.1.14. Antenna
14.1.15. The antenna with the electric drive
14.1.16. Replacement of bulbs of headlights
14.1.17. Adjustment of light of headlights
14.1.18. Headlight
14.1.19. Replacement of bulbs of an incandescence
14.1.20. Screen wiper engine
14.1.21. Sound signal
14.1.22. Check of a heater of back glass
14.1.23. Window regulators with the electric drive
14.1.24. Rear-view mirrors with the electric drive
14.1.25. Safety airbag
+ 14.2. Electroschemes
|
FORWARD TURNS AND MARKER LIGHTS
| PERFORMANCE ORDER |
|
1. Open a cowl and unscrew the screw which the forward dimensional lamp to a wing fixes. |
|
2. Having pulled forward, take a forward dimensional lamp, turn the holder of a bulb counterclockwise and take it from a lamp. |
|
3. Turn a bulb counterclockwise and take it from the holder. |
| 4. Installation is made in sequence, the return to removal. |
|
BACK LAMP
| PERFORMANCE ORDER |
|
|
| 1. Remove finishing of a luggage compartment opposite to a back lamp (shooters specified glow lamps in a back lamp). |
|
2. Turn the holder of a bulb of an incandescence counterclockwise and take it from a back lamp. |
| 3. Press and in this situation turn a bulb counterclockwise and take it from the holder of a bulb. |
| 4. Installation is made in sequence, the return to removal. |
|
THE LAMP OF THE STOPLIGHT AND BACKING LOCATED IN THE TRUNK LID
| PERFORMANCE ORDER |
|
1. Remove finishing of a trunk lid opposite to a lamp. |
| 2. Turn the holder of a bulb of an incandescence counterclockwise and take it from a back lamp. |
| 3. Press and in this situation turn a bulb counterclockwise and take it from the holder of a bulb. |
| 4. Installation is made in sequence, the return to removal. |
|
TOP STOPLIGHT
| PERFORMANCE ORDER |
| Models with a body "sedan" |
| 1. Disconnect the electric socket from the top stoplight. |
| 2. Unscrew screws of fastening of the top stoplight. |
| 3. Remove the top stoplight. |
| 4. Installation is made in sequence, the return to removal. |
| Models with a body "station wagon" |
|
5. Remove decorative caps. |
|
6. Unscrew the screws located under caps and uncover the top stoplight. |
|
7. Having pulled up, take a lamp of the top stoplight from the holder. |
| 8. Installation is made in sequence, the return to removal. |
|
ILLUMINATION OF REGISTRATION PLATE
| PERFORMANCE ORDER |
|
1. Unscrew screws, the fixing lamps of illumination of registration plate. |
|
2. Remove a plafond from a lamp of illumination of registration plate. |
|
3. Having pulled on itself, take a bulb from a lamp of illumination of registration plate. |
| 4. Installation is made in sequence, the return to removal. |
|
ILLUMINATION OF THE COMBINATION OF DEVICES
| PERFORMANCE ORDER |
| 1. Remove a combination of devices. |
|
2. Turn the holder of a bulb counterclockwise and take him from a payment of a combination of devices. |
| 3. Having pulled for a bulb, take it from the holder. |
| 4. Installation is made in sequence, the return to removal. |
|
ILLUMINATION OF SALON
| PERFORMANCE ORDER |
|
1. Using an edge of a thin screw-driver, remove a plafond of a lamp of illumination of salon. |
|
2. Take a bulb of illumination of salon from contact clips. |
| 3. Installation is made in sequence, the return to removal. |
|
|
|
