Subaru Legacy

since 1990-1998 release

Repair and operation of the car



Subaru of Legasi
+ 1.1. Identification numbers
+ 2. Maintenance
+ 3. Engines
+ 4. Heating, ventilation
+ 5. Fuel system
+ 6. Exhaust system
+ 7. Systems of start, ignition
+ 8. Transmissions
+ 9. Coupling, shaft
+ 10. Brake system
+ 11. Suspension bracket
+ 12. Steering
+ 13. Body
- 14. Electric equipment
   - 14.1. Electric equipment of a body
      14.1.1. Introduction
      14.1.2. Electric chains
      14.1.3. Detection of not closed chain
      14.1.4. Safety locks
      14.1.5. Chain breakers
      14.1.6. Relay
      14.1.7. Relay of turns and alarm light system
      14.1.8. Multipurpose switches of a steering column
      14.1.9. Ignition lock
      - 14.1.10. Replacement of switches of the dashboard
         14.1.10.1. Models from 1990 to 1994
         14.1.10.2. Models since 1995
      14.1.11. Combination of devices
      14.1.12. Radio receiver
      14.1.13. Loudspeakers
      14.1.14. Antenna
      14.1.15. The antenna with the electric drive
      14.1.16. Replacement of bulbs of headlights
      14.1.17. Adjustment of light of headlights
      14.1.18. Headlight
      14.1.19. Replacement of bulbs of an incandescence
      14.1.20. Screen wiper engine
      14.1.21. Sound signal
      14.1.22. Check of a heater of back glass
      14.1.23. Window regulators with the electric drive
      14.1.24. Rear-view mirrors with the electric drive
      14.1.25. Safety airbag
   + 14.2. Electroschemes


,


14.1.10. Replacement of switches of the dashboard

14.1.10.1. Models from 1990 to 1994

GENERAL INFORMATION

SWITCH OF ADJUSTMENT OF PROVISION OF THE MIRROR

Arrangement of contacts on the socket of the switch of adjustment of provision of a mirror and a condition of contacts on the socket at various provisions of the switch


PERFORMANCE ORDER
1. Using an edge of a thin screw-driver, take the switch from a nest in the dashboard.
2. Disconnect the electric socket from a reverse side of the switch.
3. Using an ohmmeter, check a condition of contacts of the switch of adjustment of provision of a mirror depending on position of the switch (see rice. An arrangement of contacts on the socket of the switch of adjustment of provision of a mirror and a condition of contacts on the socket at various provisions of the switch).
4. Connect the electric socket to the switch and insert the switch into a dashboard nest before its accurate fixing.

SWITCH OF THE ALARM LIGHT SYSTEM

Arrangement of contacts on the socket of the switch of the light alarm system and a condition of contacts on the socket at various provisions of the switch

PERFORMANCE ORDER
1. Remove a decorative overlay of a combination of devices.
2. Unscrew screws and remove the switch from a decorative overlay of a combination of devices.
3. Using an ohmmeter, check a condition of contacts of the switch of the light alarm system depending on position of the switch (see rice. An arrangement of contacts on the socket of the switch of the light alarm system and a condition of contacts on the socket at various provisions of the switch).
4. Install the switch on a decorative overlay of a combination of devices, fix screws, connect the electric socket, and establish a decorative overlay of a combination of devices.

SWITCH OF THE BACK FOG LAMP

Arrangement of contacts of the electric socket and condition of contacts on the socket at various provisions of the switch


PERFORMANCE ORDER
1. Using an edge of a thin screw-driver, take the switch from a nest in the dashboard.
2. Disconnect the electric socket from the switch.
3. Using an ohmmeter, check a condition of contacts of the switch of a back fog lamp depending on position of the switch (see rice. An arrangement of contacts of the electric socket and a condition of contacts on the socket at various provisions of the switch).
4. Connect the electric socket to the switch, and install the switch in a dashboard nest before accurate fixing of the switch.