Subaru Legacy

since 1990-1998 release

Repair and operation of the car


Subaru of Legasi
+ 1.1. Identification numbers
- 2. Maintenance
   2.1. Introduction
   2.2. Technical characteristics
   2.3. Frequency of service
   2.4. Check of level of engine oil
   2.5. Level of cooling liquid
   2.6. Level of brake fluid and liquid of the drive of coupling
   2.7. Liquid for a windshield washer
   2.8. Check of the accumulator
   2.9. Tires and check of pressure in tires
   2.10. Check of level of oil in an automatic transmission
   2.11. Check of level of liquid in the amplifier of a steering
   2.12. Replacement of oil and oil filter
   2.13. Check and service of the accumulator
   2.14. Battery charging
   2.15. Check of the cooling system
   2.16. Check of hoses, tubes and their replacement
   2.17. Check and replacement of brushes of screen wipers
   2.18. Shift of tires
   2.19. Check of a suspension bracket and steering
   2.20. Check of an exhaust system
   2.21. Check of level of oil in a transmission and the main transfer
   2.22. Check of level of oil in differential (the main transfer)
   2.23. Check of brake system
   2.24. Check of the vacuum amplifier of brakes
   2.25. Check of the emergency brake
   2.26. Check of fuel system
   2.27. Replacement of the fuel filter
   2.28. Check and replacement of a driving belt
   2.29. Check of a free wheeling of a pedal of a brake
   2.30. Check of a free wheeling of a pedal of coupling
   2.31. Check and replacement of spark plugs
   2.32. Check of high-voltage wires
   2.33. Check and adjustment of turns of idling
   2.34. Replacement of the air filter
   2.35. Check and replacement of the valve of ventilation of a case (PCV)
   2.36. Check of system of catching of vapors of fuel
   2.37. Check of system of repeated burning of exhaust gases (EGR)
   2.38. Service of the cooling system
   2.39. Replacement of brake fluid
   2.40. Replacement of oil in an automatic transmission
   2.41. Replacement of oil in a mechanical transmission
   2.42. Check and adjustment of gaps of valves
   + 2.43. Main malfunctions
+ 3. Engines
+ 4. Heating, ventilation
+ 5. Fuel system
+ 6. Exhaust system
+ 7. Systems of start, ignition
+ 8. Transmissions
+ 9. Coupling, shaft
+ 10. Brake system
+ 11. Suspension bracket
+ 12. Steering
+ 13. Body
+ 14. Electric equipment


скачать онлайн 3a942d17

2.17. Check and replacement of brushes of screen wipers
GENERAL INFORMATION

Brushes and rubber elements need to be checked for existence of wear, cracks and damages periodically.

Check

PERFORMANCE ORDER
1. The film from pitch and dirt formed on brushes, reduces efficiency of their work therefore brushes need to be washed out clear water with soap from time to time.
2. In the mechanism of the drive of brushes of screen wipers can weaken fastening bolts therefore when checking brushes of screen wipers it is also necessary to check and tighten all fastenings (on a photo – a tightening of a nut of fastening of the lever of a screen wiper).
3. If rubber elements are worn-out, cracked or deformed or badly clear glass, they need to be replaced with the new.

Replacement

PERFORMANCE ORDER
1. Raise the screen wiper brush lever from a windshield.
2. From two parties squeeze steel amplifiers of a rubber tape (it is specified by an arrow) a screen wiper and take a rubber tape of a screen wiper from a brush end face.
3. Establish a new rubber tape in a brush so that captures of a brush were established for the steel amplifier of a rubber tape, and move a rubber tape into a screen wiper brush.